Search for question
Question

5 A farmer's market is considering the addition of bar code scanners at their check-out counters, which would use the UPC marked on all grocery packaging. Currently, the checkout clerk keypunches the price of each item into the register during check-out. Observations indicate that an average of 50 items are checked out per customer. The clerk currently takes7 seconds per item to keypunch the register and move the item along the check-out table.On average it takes 25 seconds to total the bill, accept money from the customer, and make change. It then takes 4 seconds per item for the clerk to bag the customer's order. Finally,about 5 seconds are lost to transition to the next customer. Bar code scanners would eliminate the need to keypunch each price, and the time per item would be reduced to 3 seconds with the bar code scanner. (a) What is the hourly throughput rate (number of customers checked out per hour) under the current check-out procedure? (b) What would be the estimated hourly throughput rate if bar code scanners were used? (c) If separate baggers were used instead of requiring the check-out clerk to perform bagging in addition to check-out,what would be hourly throughput rate? Assume that bar code scanners are used by the clerk. (d) Determine the productivity index for each of the two cases in (b) and (c), using(a) as the basis of comparison and hourly customers checked out per labor hour as the measure of productivity.

Fig: 1


Most Viewed Questions Of Strength Of Material

11. The truss ABC shown in the figure supports a horizontal load P and a vertical load P2. Both bars have cross-section area A and are made of steel with Young's modulus E. Determine the strain energy in the truss.


6.14. A 2 m x 3 m spread footing placed at a depth of 2 m carries a vertical load of 3000 kN and a moment of 300 kN-m, as shown in Figure P6.14. Determine the factor of safety using Meyerhof's effective area method.


6.7. Determine the maximum column load that can be applied on a 1.5 m x 1.5 m square foundation placed at a depth of 1.0 m within a soil, where y= 19.0 kN/m, d = 10 kN/m^2, and = 24°. Allow a factor of safety of 3.0.


2B. Calculate the total building seismic base shear, V, in the north-south direction only.Assume the total seismic weights of each floor are: Roof = 150 kips, 3rd Floor = 700 kips,2nd Floor = 900 kips (note these are not the answers to 2A!). Use Ss = 0.616, Sj = 0.274.The lateral force resisting system is a Building Frame System with special reinforced concrete shear walls. The building capacity is more than 500 students (Risk Category Ill)and the soil site class is D.


If for a strain gauge, the Gage Factor is given as 2, and nominal gauge resistance R given is 120 Ohm,what will be the change in resistance for a strain of 5 micro strains, (equivalent to 50 psi for Aluminum)?


A solid 40-mm-diameter shaft is used in an aircraft engine to transmit 115 kW at 1,300 rpm to a propeller that develops a thrust of 15 kN. Determine the principal stresses and the maximum shear stress at any point on the outside surface of the shaft.


A hollow steel shaft is expected to transmit 4200 N-m of torque and is to be sized so that the torsional stress does not exceed 120 MPa. (a) If the inside diameter is 70 percent of the outside diameter, what size shaft should be used? Use preferred sizes. (b) What is the torsional stress on the inside of the shaft when full torque is applied?


For the support of Prob. 1.47, knowing that the diameter of the pins d = 16 mm and that the magnitude of the load is P 20 kN,determine (a) the factor of safety for the pin, (b) the required values of b and e if the factor of safety for the wooden member is the same-as that found in part a for the pin.


Suppose you want to connect a remote speaker to your stereo. It needs to be 100 inches away.You are using copper wire. What should be the diameter of the wire if the resistance of each wire must be less than 0.10 Q? (3 marks) \text { Given: (Resistivity of copper } \left.=1.7 \times 10^{-5} \mathrm{~W}_{\mathrm{m}}\right)


4. When removing a wheel to change a flat tire, a driver applies an equal force (P = 25lb) at the ends of two of the arms of a lug wrench (see figure below). The wrench is made of steel with a shear modulus of elasticity G=11.4x10^6 psi. Each arm of the wrench is 9.0in. long and has a solid circular cross section of diameter d=0.5in. а.Determine the maximum shear stress in the arm that is turning the lug nut (arm A) b. Determine the torsional deflection (in degrees) of this same arm