Search for question
Question

A FWD vehicle has the following data:

Front axle weight: 1750 lbs

Center of gravity height: 17 inch

Air drag coefficient: 0.32

Tire radius: 11.70 in.

Powertrain efficiency: 0.94

Max. Power @6000RPM: 138 HP

Torque(ft.lb)

The manual transmission used for the vehicle has six forward speeds and the gear ratios are: first gear

(3.72), 2nd gear (2.31), 3rd gear(1.51), 4th gear (1.07), 5th gear (0.81), 6th gear (0.63). The engine WOT

output plot is given below:

140

130

120

110

100

90

80

0

Torque

1000

Homework 1

2000

3000

4000

Rear axle weight: 1550 lbs

Wheel base: 104 in.

Frontal projected area: 22.90 square feet

Roll resistance coefficient: 0.018

Traction coefficient: 1.0

Max. Torque @4500RPM: 132 ft.lb.

Speed (RPM)

Power

5000

6000

150

125

100

75

+50

8

25

7000

Power(HP)/na) The engine RPM drops 662 (RPM) when a 4-5 upshift is made at a vehicle speed of 45 mph.

Determine the final drive ratio of the vehicle.

b)

Determine the engine torque and the engine power when the vehicle is cruising at a constant speed of

65 mph on level ground in the 6th and 5th gear respectively.

c)

Determine the maximum acceleration the vehicle can achieve in the 4th gear at a speed of 65 mph on a

2% slope.

d)

What is the highest speed the vehicle can achieve in the 6th gear on level ground?

f)

e) Redesign the 6th gear ratio for the highest vehicle speed possible based on maximum engine power.

Redesign the gear ratio for the lowest gear for the maximum gradability using a reservation

factor 3 = 1.35.

Fig: 1

Fig: 2


Most Viewed Questions Of Automobile Engineering

Tire of Porsche 911 turboTM A model of Porsche 911 turboTM uses the following tires. front : 235/35ZR19rear : 305/30ZR19 Determine and compare hr, and D for the front and rear tires.


For the crank-slider linkage shown shown on the next page with the corresponding nominclature set up the matrix equations to determine the unknown pin forces in x-, y-components and the unknown torque required to drive the system. For matrices other than the unknown forces, only one numeric value should be in each matrix location. Do not solve matrix equations. following is given fp1 is an external force applied at the center of gravity of link 3 FP is an applied force at the center of gravity of the slider


Tasks to be done: 1. Literature review (general information on Chem-E-Car, reactions and reactors applied on current competed prototypes) 2. Description of possible 3 available designs (propulsion mechanism, stopping mechanism, reactor type, kinetics, etc.) 3. Engineering Analysis: a. Proposal of your unique idea to identify a need or problem or improve and existing design. b. Identify design criteria and constraints (chemicals, constructing materials, safety and environmental aspects) c. Schematic of physical prototype of the car (MS powerpoint, MS Visio, or any suitable software.


power of the battery is given and the weight of the car and the driver are given, need to calculate how much power do we need to reach the maximum speed Datas Chassis is 25 kg Driver is 70kg Battery is 5 kg Capacity = AH20


Problems 1 The stick diagram of a six-speed RWD MT is shown Figure 2.9b. The tire radius of the vehicle is R (ft) and the final drive ratio i is 3.25. The numbers of teeth are labeled in the drawing. Some gear ratios are given as: 1st gear (3.92), 2nd gear (2.76), 3rd gear (1.91), 4th gear (1.41). The number of teeth of gears N; and N, are 19 and 23 respectively. a) Determine the equivalent mass moment of inertia to be synchronized in a 1-2 upshift and a 5-4 downshift respectively, in terms of the mass moments of inertia of the involved parts and the labels for the tooth numbers. b) A 2-3 upshift is to be made at a vehicle speed of V (mph). Assuming the synchro- nization time is At and the angular velocity change is uniform during synchro- nization, determine the friction torque to be generated by the synchronizer friction cones. c) Determine the work done by the friction and the angle of rotation of gear N4c in the process of synchronization for the shift in (b). d) The synchronizers used in the transmission are the same and the angular velocity change during synchronization is assumed to be uniform. If the magnitude of the shift force in a 2-3 upshift, F23, is 10 N, determine the magnitude of the shift force in a 1-2 upshift, F12. Both shifts are made at the same engine angular veloc- ity, and within the same synchronization time At.


c A 5-4 shift is to be made at a vehicle speed of V (mph) with a synchronization time Ar. Assuming uniform angular velocity change during synchronization, find the friction torque to be generated by the friction cones.


Prob. 2: The stick diagram of a 5-speed marmal transmission of a RWD vehicle is shown in the drawing. The tire mndius of the vehicle is R (ft) and the final drive ratio is t,. The mambers of gear teeth are labeled in the stick diagram. Determine the transmission ratios in terms of the numbers of gear teeth for all forward and reverse gears. Determine the equivalent mass moment of inertia to be synchronized in a 2-3 shift and in a 5-4 shift respectively, in terms of the gear tooth numbers and the mass moments of inertia of the involved parts. A 5-4 shift is to be made at a vehicle speed of V (mph) with a synchronization time Ar. Assuming uniform angular velocity change during synchronization, find the friction torque to be generated by the friction cones. d) Determine the angles of rotation of the two friction cones during the synchronization process in the shift in e). Also determine the angle of rotation of the input shaft during the synchronization process. 5th 5th-Rev. Synchro Input Shaft N: et the Nc Rak 1st 2nd 3rd -Neo IVI 11²307 NOJAT Nee 1-2 Synchro NIC Reverse Idler Não 4th output shaft / Counter Shaft 3-4 synchro.


Location Features Design Aspects (material, styling, etc.) Would you suggest any changes? Why? What could be the side effect? Image (add picture of each item) Front Tray Upper Cover Console Bin


d) Determine the angles of rotation of the two friction cones during the synchronization process in the shift in c). Also determine the angle of rotation of the input shaft during the synchronization process.


A FWD vehicle has the following data: Front axle weight: 1750 lbs Center of gravity height: 17 inch Air drag coefficient: 0.32 Tire radius: 11.70 in. Powertrain efficiency: 0.94 Max. Power @6000RPM: 138 HP Torque(ft.lb) The manual transmission used for the vehicle has six forward speeds and the gear ratios are: first gear (3.72), 2nd gear (2.31), 3rd gear(1.51), 4th gear (1.07), 5th gear (0.81), 6th gear (0.63). The engine WOT output plot is given below: 140 130 120 110 100 90 80 0 Torque 1000 Homework 1 2000 3000 4000 Rear axle weight: 1550 lbs Wheel base: 104 in. Frontal projected area: 22.90 square feet Roll resistance coefficient: 0.018 Traction coefficient: 1.0 Max. Torque @4500RPM: 132 ft.lb. Speed (RPM) Power 5000 6000 150 125 100 75 +50 8 25 7000 Power(HP)/na) The engine RPM drops 662 (RPM) when a 4-5 upshift is made at a vehicle speed of 45 mph. Determine the final drive ratio of the vehicle. b) Determine the engine torque and the engine power when the vehicle is cruising at a constant speed of 65 mph on level ground in the 6th and 5th gear respectively. c) Determine the maximum acceleration the vehicle can achieve in the 4th gear at a speed of 65 mph on a 2% slope. d) What is the highest speed the vehicle can achieve in the 6th gear on level ground? f) e) Redesign the 6th gear ratio for the highest vehicle speed possible based on maximum engine power. Redesign the gear ratio for the lowest gear for the maximum gradability using a reservation factor 3 = 1.35.