maintenance engineering homework help

Boost your journey with 24/7 access to skilled experts, offering unmatched maintenance engineering homework help

Trusted by 1.1 M+ Happy Students

4.4Trust Pilot

4.4Edu Reviewer

5App Review

4.8Student

4.2Sitejabber

Recently Asked maintenance engineering Questions

Expert help when you need it

Q1: Q1). DESCRIBE THE PURPOSE OF CABLES THAT USED ON AIRCRAFT? Q2). EXPLAiN THE MAINTENANCE & INSPECTION OF: > SPRINGS. > DRIVE BELTS. > SCREWJACKS. > PUSH PULL RODS. > LEVERS. > V'-BAND CLAMPS, THAT MAY USED ON AIRCRAFT OPERATIONS?See Answer
Q2:1. The normal time to perform the regular work cycle for a certain manual operation is 3.23 min. In addition, an irregular work element whose normal time is 1:25 min must be performed every 5 cycles. The PFD allowance factor is 15%. Determine (a) the standard time (b) how many work units are produced if the worker's performance in an 8-hour shift is standard. 2. Determine the anticipated amount of time lost per 8-hour shift when an allowance factor of 15% is used, as in the previous question. 3. Now that the standard is set (T= 4.00 min) and given the data from the previous questions how many work units would be produced if the worker's average performance during an 8-hour shift were 125% and the hours worked were exactly 6.956 hour, which corresponds to the 15% allowance factor.See Answer
Q3:1. The normal time for a repetitive task that produces two work units per cycle is 3.0 min. The plant uses a PFD allowance factor of 15%. Determine (a) the standard time per piece and (b) how many work units are produced in an 8-hour shift at standard performance. 2. The normal time to perform a repetitive manual assembly task is 4.25 min. In addition, an irregular work element whose normal time is 1.75 min must be performed every 8 cycles. Two work units are produced each cycle. The PFD allowance factor is 16%. Determine (a) the standard time per piece and (b) how many work units are produced in an 8-hour shift at standard performance. (c) Determine the anticipated amount of time worked and the amount of time lost per 8-hour shift that corresponds to the PFD allowance factor of 16%. 3. A worker performs a repetitive assembly task at a workbench to assemble products. Each product consists of 25 components. Various hand tools are used in the task. The standard time for the work cycle is 7.45 min, based on using a PFD allowance factor of 15%. If the worker completes 75 product units during an 8-hour shift, determine (a) the number of standard hours accomplished and (b) worker efficiency. (c) If the worker took only one rest break, lasting 13 min, and experienced no other interruptions during the 8 hours of shift time, determine her worker performance.See Answer
Q4:You have to prepare a training plan for a trainee at the university in the Operation and Maintenance Department in Electricity. Plan for the internship program is given below. A sample report is given, you can check that to see what all to include.See Answer
Q5:Question A) Deduce the type of failures (either ductile or brittle) for the metals in each image and justify your deduction. B) Discuss how each failure can be monitored via a NDT method. C) How can both types of failure be controlled in the future?See Answer
Q6:Question Fatigue failure was the root cause of this metal gear failure A) Use the image to confirm this root cause. B) How can fatigue failure in this gear be controlled in the future?See Answer
Q7:Explain the reason/s for creep failure and how could you prevent this type of failure. Creep failure visual appearance This carbon steel furnace tube should have given good service for ten years. It ruptured after one year. The failed tube showed obvious swelling at the point of rupture. The tube wall was thinned to a knife edge at the rupture.See Answer
Q8:Question A reformer tube in this reformer has succumbed to creep failure, A) What are some NDT techniques that can be use to monitor creep in the remainder of tubes? B) What are some possible reasons for this failure? TIMESee Answer
Q9:Question Cavitation has occurred in on a ship's propeller. The ship owner is considering a new in-kind replacement propeller. Advise on a recommendation to control cavitation in the future. Suggest another option to the owner instead of an in-kind replacement. BlakeSee Answer
Q10:Question The back side of the sliding bearing shown has succumbed to fretting. Recommend ways to control this fretting from occurring in the future. Justify in terms of cost, practicality, and applicability. ASee Answer
Q11:Question What are some potential causes for spalling that occurred in the inner race of this bearing?See Answer
Q12:Question • In this image of a valve stem, identify whether the failure has occurred due to distortion or fracture. Justify your answer 02113-1 9 10 11 2 fr HE 4 EMSee Answer
Q13:Question Hydrogen-induced blistering occurred in a 9.5 mm thick carbon steel plate (ASTM A 285, grade that had been in service one year in a refinery vessel). A) Use the image to confirm this root cause. B) How can hydrogen-induced blistering be controlled in the future? Adapted from ASM Metals Handbook Volume 11See Answer

TutorBin Testimonials

I found TutorBin Maintenance Engineering homework help when I was struggling with complex concepts. Experts provided step-wise explanations and examples to help me understand concepts clearly.

Rick Jordon

TutorBin experts resolve your doubts without making you wait for long. Their experts are responsive & available 24/7 whenever you need Maintenance Engineering subject guidance.

Andrea Jacobs

I trust TutorBin for assisting me in completing Maintenance Engineering assignments with quality and 100% accuracy. Experts are polite, listen to my problems, and have extensive experience in their domain.

Lilian King

I got my Maintenance Engineering homework done on time. My assignment is proofread and edited by professionals. Got zero plagiarism as experts developed my assignment from scratch. Feel relieved and super excited.

Joey Dip

Popular Subjects for maintenance engineering

You can get the best rated step-by-step problem explanations from 65000+ expert tutors by ordering TutorBin maintenance engineering homework help.

TutorBin helping students around the globe

TutorBin believes that distance should never be a barrier to learning. Over 500000+ orders and 100000+ happy customers explain TutorBin has become the name that keeps learning fun in the UK, USA, Canada, Australia, Singapore, and UAE.