powder metallurgy homework help

Boost your journey with 24/7 access to skilled experts, offering unmatched powder metallurgy homework help

Trusted by 1.1 M+ Happy Students

4.4Trust Pilot

4.4Edu Reviewer

5App Review

4.8Student

4.2Sitejabber

Recently Asked powder metallurgy Questions

Expert help when you need it

Q1: Question 9. (a) What are the three major reactions that occur during chain polymerization?(b) What are two methods by which a linear chain polymerization reaction can be terminated? (5 points)See Answer
Q2: Question 8. Using Pauling's equation (in Chapter 2), compare the percent covalent character of the following compounds: hafnium carbide (HfC), titanium carbide (TiC), tantalum carbide (TaC), boron carbide (BC), and silicon carbide (SiC).(5 points)See Answer
Q3: What safety gear should be used when operating the table saw?See Answer
Q4: Question 7. The nose cap and the wing leading edges of the space shuttle may reach temperatures of up to1650°C. (a) Would the silica fiber compound (HRSI) be a suitable candidate for these sections of the shuttle?(b) If not, select a suitable material for this location. (c) List the important properties of the selected material that satisfy the design needs.(5 points)See Answer
Q5: Question 2. HFO2 has the CaF2 crystal structure. Calculate the density of HfO2 in kg/m³ if the ionic radii are Hf** = 0.083 nm and O2 =0.132 nm. (4 points)See Answer
Q6: (a) Why is the Fe-Fe3C phase diagram a metastable phase diagram instead of a true equilibrium phase diagram? (1 points) (b) Define the following phases that exist in the Fe-Fe3C phase diagram: (i) austenite, (ii) a ferrite, (iii)cementite, (iv) 8 ferrite. (2 points) (c) Write the reactions for the three invariant reactions that take place in the Fe-Fe3C phase diagram. (3points)See Answer
Q7: Question 4. An austenitized 4340 standard steel bar is cooled at different rates (see Figure 2).Predict what will be the constituents in the microstructure of the bar at 200°C for the following cooling rates:(6 points) (a) 5°C/s (51-mm from the quenched end of a Jominy bar) (b) 8°C/s (19.0-mm from the quenched end of a Jominy bar) (c) 50°C/s (9.5-mm from the quenched end of a Jominy bar) See Answer
Q8: Question 5. A metal-matrix composite (MMC) is made of a 6061-Al alloy matrix and continuous boron fibers.The boron fibers are produced with a 15.5 um diameter tungsten-wire core that is coated with boron to make a final 107 um diameter fiber. A unidirectional composite is made with 63 vol % of the boron fibers in the Al6061 matrix. Assuming the law of mixtures applies to isostrain conditions, calculate the tensile modulus of the composite in the direction of the fibers. Data are EB = 370 GPa, Ew = 410 GPa, and EAI = 70.4 GPa. (5 points)See Answer
Q9: Question 6. Calculate the average molecular weight Mm for a thermoplastic that has the following weight fractions fi for the molecular weight ranges listed:(5 points) See Answer
Q10: Question 3. Figure 1 illustrates the deformation mechanisms in polymers. (4 points) (a) Which mechanism is dominant in the stretching of a rubber band? (b) Which mechanism(s) represent plastic deformation? (c) Which mechanism is pronounced in polyethylene above its glass transition temperature? (d) Which mechanism is associated with the highest elastic modulus? See Answer
Q11: List the similarities and differences of forging and compacting metal powders.(Graduate students only)See Answer
Q12: Describe the features of a screw extruderand its functions.See Answer
Q13: Are there applications in which you, as a manufacturing engineer, would not recommend a PM product? Explain.See Answer
Q14: Compare thermoplastics and thermosets in terms of material properties and its effect on the possible manufacturing process that can be used to create parts from each material.See Answer
Q15: Describe the blow molding process in terms of its steps, capabilities, type of materials used, and final products.See Answer
Q16: Why is there density variation in the compacting of powders? How is it reduced?See Answer
Q17: Explain why the mechanical and physical properties of PM parts depend on the powder distribution, shape, and size.See Answer
Q18: The axisymmetric part shown in the accompanying figure is to be produced from fine copper powder and is to have a tensile strength of150 MPa. Determine the compacting pressure and the initial volume of powder needed 25Dimensions in mm해야12-20→25See Answer
Q19: Explain why in rotational modeling we only can create thin-walled parts.See Answer
Q20: Name the various methods of powder production and list what is the major features for each method.See Answer

TutorBin Testimonials

I found TutorBin Powder Metallurgy homework help when I was struggling with complex concepts. Experts provided step-wise explanations and examples to help me understand concepts clearly.

Rick Jordon

TutorBin experts resolve your doubts without making you wait for long. Their experts are responsive & available 24/7 whenever you need Powder Metallurgy subject guidance.

Andrea Jacobs

I trust TutorBin for assisting me in completing Powder Metallurgy assignments with quality and 100% accuracy. Experts are polite, listen to my problems, and have extensive experience in their domain.

Lilian King

I got my Powder Metallurgy homework done on time. My assignment is proofread and edited by professionals. Got zero plagiarism as experts developed my assignment from scratch. Feel relieved and super excited.

Joey Dip

Popular Subjects for powder metallurgy

You can get the best rated step-by-step problem explanations from 65000+ expert tutors by ordering TutorBin powder metallurgy homework help.

TutorBin helping students around the globe

TutorBin believes that distance should never be a barrier to learning. Over 500000+ orders and 100000+ happy customers explain TutorBin has become the name that keeps learning fun in the UK, USA, Canada, Australia, Singapore, and UAE.